Water off, leak found, repair proven under pressure.
Burst pipe repairs and water pipe renewals across inner Melbourne, from a failed copper joint to ageing pipework that needs replacing. The water is isolated first, the source confirmed, and every repair pressure tested before the area is closed.
- Licensed & insured
- Pressure tested before close-up
- Inner Melbourne
Repair or renew, decided by the pipe.
A burst or leaking water pipe wrecks plaster, flooring and cabinetry quickly, which is why the order of work matters. Measured Plumbing isolates the water first, confirms where the failure actually is, and only then opens up the smallest sensible access. Once the pipe is exposed, its condition decides the scope: a clean repair of the failed section, or a renewal of the run.
Where one joint has let go and the pipe either side is sound, a repair is the right spend: the failed section comes out, the line is tested and the access is closed. A renewal makes more sense when the same run has leaked more than once, or when the pipe shows corrosion, pinholing or thinning as soon as it is cut.
Nothing is priced until the pipe has been seen. Once it has, you get a written scope that says what gets replaced, how far the run goes and what is excluded, and where the water damage looks claimable, the cause and affected areas are documented for the claim.
From one failed joint to a full re-pipe.
The right scope depends on where the leak is, what caused it and the condition of the pipework around it.
Burst pipe repair
The failed section cut out and replaced in copper or approved pressure pipe, then the line tested before close-up.
Leaking copper repair
Pinholed and corroded sections replaced rather than clamped, wherever the condition of the pipe calls for it.
Water pipe renewals
Part or all of the water service re-piped through a house, unit or shop, staged so you keep water overnight wherever the layout allows.
Concealed pipe leaks
In-wall, subfloor and under-slab supply leaks located precisely before anything is opened up, so the access hole is small.
Pressure and isolation valves
A limiting valve fitted where pressure is running high, and isolation points added so the next fault is off in seconds.
Flexi hose replacement
Aged braided hoses under basins, sinks and toilets swapped out as preventative work during any visit.
Strata and managed properties
Shared risers and common water lines, with the scope documented for the manager or committee to approve before work starts.
Water service and mains
The supply line from the meter to the building repaired or replaced where it has failed or is failing.
What a pipe repair covers.
The quote sets out what gets replaced, how far it runs and what is excluded, so there is no gap between the plumbing and the finish.
- Water isolated and pressure taken out of the affected line
- Leak located by fixture, run and depth before any access is cut
- Access opened in the smallest sensible place
- Pipe condition assessed once exposed, with repair or renewal called on what we find
- Failed section replaced in copper or approved pressure pipe
- Correct supports and lagging on new pipework
- Line pressure tested before anything is closed
- Fixtures checked for flow and temperature afterwards
- Access closed up, or left ready for the patching trade as agreed
- Site cleaned before we leave
- Cause and affected areas documented where an insurance claim is likely
Houses, apartments, shops and managed buildings.
Where the pipe runs, and who is responsible for it, shapes the job.
- 01
Older houses with galvanised steel or early thin-walled copper, where corrosion along a run usually points to renewal rather than a third repair.
- 02
Apartments, where the internal isolation valve may sit under the sink or in the laundry and building management may need to isolate the shared riser.
- 03
Rental properties, where the repair is the owner's responsibility and the call-out is usually authorised by the property manager.
- 04
Strata buildings, where pipework serving one lot is generally the owner's and shared risers belong to the owners corporation, so the scope is documented for whoever approves it.
- 05
Shops and small commercial tenancies needing a partial or full re-pipe, staged to keep water on where possible.
- 06
Homes about to renovate a bathroom or kitchen, where renewing the pipework while the walls are open beats repairing it twice.
If you are not sure whose pipe it is, send what you know and we will tell you who needs to approve the work.
Pipe repairs and renewals across the inner suburbs.
Failed joint replaced
A failed copper joint cut out and replaced, with the line pressure tested before the access was closed.
Concealed leak repair
Access cut in the smallest sensible place to reach and replace a leaking section of supply pipe.
Water service renewal
New copper pipework with correct supports and lagging on a water service renewal.
What affects the cost of a burst pipe repair.
The pipe itself is the cheap part. What moves the price is getting to it: whether the failure sits in a wall, a ceiling, the subfloor or under a slab, how much of the run has to be exposed, whether tiles or cabinetry come off to reach it, and whether the property can stay without water while the work happens.
For a renewal, the length of the run and how many fixtures hang off it set the price. Nothing is quoted until the pipe has been seen, and the written quote states the reinstatement up front: plaster patching and tiling usually sit with a separate trade, and the quote says exactly where the plumbing stops.
Scope, inclusions and exclusions, in writing.
Anything outside what was agreed is priced and approved before it proceeds, so no variation lands on an invoice unannounced.
How a burst pipe repair runs.
- 01
Isolate the water
The water goes off and the pressure comes out of the affected line before anything else.
- 02
Locate the leak
Found by fixture, run and depth, so the access hole goes in the right place the first time.
- 03
Cut clean access
The smallest sensible opening is cut and the pipe condition assessed as soon as it is exposed.
- 04
Replace or renew
The failed section replaced, or the run renewed, in copper or approved pressure pipe with proper supports and lagging.
- 05
Pressure test
The line is tested under pressure and every fixture checked for flow and temperature.
- 06
Close up and clean
Access closed, or left ready for the patching trade, and the site cleaned before we leave.
Water pouring out right now?
Turn it off at the meter, open an outside tap to drop the pressure, keep clear of wet electrics, and call. Isolation first, then the repair.
What customers say, in their own words.
“I was extremely impressed by the efficiency, professionalism and service provided. Cannot recommend them enough!”
“Had an issue with my washing machine, hot water service and toilet all in the one day, ultra quick turnaround and couldn't have been more thankful for the job done. Completely saved the day and will absolutely use again for my next issue.”
“I recently used this new plumbing company and couldn't be happier with the experience. From the initial phone call through to the completion of the job, the team was professional, friendly, and incredibly responsive.”
Richmond-based, across inner Melbourne.
Melbourne CBD and the inner suburbs: inner city, inner east, inner north, inner south and bayside. Not sure if your suburb is covered? Ask.
Common questions, answered plainly.
Can't find what you need? Call 0416 812 147 or send an enquiry and Heath will get back to you.
Other work we cover regularly.
Emergency Plumbing
Burst pipes, gas leaks, no hot water and flooding. Urgent call-outs across inner Melbourne, subject to availability.
Learn more
Residential Maintenance & Repairs
Repairs and maintenance for houses, apartments and rentals, from leaking fixtures and pressure faults to general plumbing problems.
Learn more
Hot Water Systems
Fault finding, repairs and replacements sized to the property, its demand and the existing connections.
Learn moreTalk to Heath about a burst or leaking pipe.
If water is escaping now, call. Otherwise send what you know, a photo of the leak or the meter helps, and Heath will come back with the next step.